Powermatic PJ882 Instrukcja Użytkownika

Operating Instructions and Parts Manual 8-inch Parallelogram Jointer Model PJ-882 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123

10Installing Switch Arm 1. The switch arm was shipped in horizontal position. Loosen and remove the four socket head cap screws and flat washers on

11The cutterhead guard should now have sufficient spring tension. Test it by swinging the guard away from the fence and then releasing it. The guard

12Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug. Repair or replace

13 If you are hard-wiring the Jointer, make sure the fuses have been removed or the breakers have been tripped in the circuit to which the Jointer wi

14NOTE: After operating the machine for a short time, the drive belt tension should be re-checked, as the new drive belt may stretch slightly during

153. Tighten locking handle (B, Figure 14). To tilt fence backward: The fence can be tilted backward up to 45° (that is, for a total angle of 135° f

164. Rotate the screw (H, Figure 17) until it contacts the casting in front of it. 5. Tighten the hex nut on the screw (H, Figure 17) and tighten l

172. Knives must be set in the cutterhead so that the highest point of their arc is level with the the outfeed table. 3. Knives must be parallel wi

18 9. Each table has four cam adjustment devices; two in front and two in back. NOTE: On the front of the Jointer, the two outside cams are conceale

19When you receive the jointer, the knives have been pre-set at the factory. However, the height and parallelism of the knives with the outfeed table

2 This manual has been prepared for the owner and operators of a Model PJ-882 Jointer. Its purpose, aside from machine operation, is to promote safet

20Figure 27 illustrates the correct setting of outfeed table level with the knives. The workpiece will rest firmly on both tables with no open space

2110. Place the aluminum knife gauge at the front of the outfeed table (toward the rabbet ledge) and repeat the process. 11. This test should be perf

2221. The tightening process should continue at least two more times, each time tightening the gib screws further on all three knives in turn. On the

23Infeed Table Stop Screws The stop screws below the infeed table have the same function as those for the outfeed table. See “Outfeed Table Stop Scre

24Eliminating “Play” in Tables There are four set screws at the front of the jointer – two on the outfeed table and two on the infeed table – that wi

253. The cutterhead guard must be in place and operating properly (except when rabbeting). 4. Infeed table set for desired depth of cut. 5. Stand

26Rabbeting A rabbet cut requires removal of the guard. Use extreme caution and keep hands clear of cutterhead. Always re-install guard immediately

27 Although the fence may be tilted in or out for a bevel cut, it is recommended for safety reasons that the fence be tilted in toward the operator,

28Maintenance Disconnect machine from power source before doing any maintenance. Failure to comply may cause serious injury. The table and fence sur

29Knives can usually be whetted several times in the cutterhead before having to be removed and re-ground. TIP: If the jointer is used frequently, ke

3 Table of Contents Warranty and Service ...

30Troubleshooting – Operating Problems Trouble Probable Cause Remedy Finished stock is concave on back end. Knife is higher than outfeed table. Rais

31Troubleshooting – Mechanical and Electrical Problems Trouble Probable Cause Remedy No incoming power. Verify unit is connected to power, on-button

32Trouble Probable Cause Remedy Miswiring of the unit. Double check to confirm all electrical connections are correct. Refer to appropriate wiring d

33Parts List: Cutterhead Assembly Index No. Part No. Description Size Qty ...PJ882-CHA... Cutterhead Assembly (Items 1 th

34Parts List: Fence Assembly Index No. Part No. Description Size Qty ...PJ882-FA... Fence Assembly (Index #1 thru #48)

35Fence Assembly

36Parts List: Outfeed Table and Base Assembly Index No. Part No. Description Size Qty 1...PJ882-201 ... Rear (Outfeed) Tab

37Outfeed Table and Base Assembly

38Parts List: Infeed Table Assembly Index No. Part No. Description Size Qty 1...PJ882-301 ... Front (Infeed) Table...

39Index No. Part No. Description Size Qty 56...PJ882-246 ... Key...

4 Electrical Connections – 1 Phase, 230 Volt ...44 Electrica

40Infeed Table Assembly

41Parts List: Stand Assembly Index No. Part No. Description Size Qty 1...VB-A50 ... Belt...

42Index No. Part No. Description Size Qty 40...TS-081B022... Pan Head Screw... #8

43Stand Assembly

44Electrical Connections – 1 Phase, 230 Volt

45Electrical Connections – 3 Phase, 230 Volt

46Electrical Connections – 3 Phase, 460 Volt

47

48 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

5 Warning 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on t

6 23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The righ

7 Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a Model PJ-882 Jointer. This manu

8 Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not disca

9 Installation and Assembly Tools required for assembly Forklift or hoist with straps/slings 14mm (or 9/16”) wrench or socket Cross-point (Phillips)