Powermatic PM3000 Instrukcja Użytkownika

Instructions and Parts Manual 14-inch Cabinet Saw Model PM3000 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tenn

10Blade Installation/Replacement Use care when working with or around sharp saw blade to prevent injury! To install or replace a blade (refer to Fig

11Motor Cover Line up the door hinges (A. Figure 7) with the cabinet hinges (B, Figure 7) and insert hinge pins (C, Figure 7). Note: The locking mec

12Adjustment The clamping blocks (L, M, Figure 9) are adjusted at the factory and no further adjustment of the blade guard and riving knife assembly

13Adjustments Handwheel Adjustments Referring to Figure 10: The front handwheel (B) controls the raising and lowering of the blade (blade height). T

14 Never use a zero-clearance insert with the saw blade in a tilted position. Never operate the saw without the blade guard, riving knife and anti-ki

15Tilt Stop Adjustment 1. Adjust the blade tilt for 90º as described in Blade Tilt Adjustment on page 13. 2. Using a combination square, check the 9

16 Extension plate The extension plate (D, Figure 14) can be adjusted by sliding to the right or left or removed entirely. To adjust – loosen two l

17Riving Knife Adjustment Lateral alignment The saw blade and riving knife must be in line as close as possible with each other (lateral alignment)

18Referring to Figure 18: 2. With a 5mm hex wrench, loosen two socket head button screws (E). Note: These screws are accessible through openings on

19Operations (NOTE: The following Figure illustrations may or may not show your specific table saw model, but the procedures are identical.) Overview

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure t

21When ripping long boards, use a support at the front of the table, such as a roller stand, and a support or "tailman" at the rear as show

22Bevel and Miter Operations Bevel Cut – A bevel cut is a special type of operation where the saw blade is tilted at an angle less than 90 degrees to

23Safety Devices Feather Board and Push Blocks A push stick is included with the PM3000 table saw. In addition, a multitude of after market products

24Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Cleani

25Troubleshooting Trouble Probable Cause Remedy Excessive vibration. Tilt or raising clamp knobs not tightened. Tighten knobs. Blade out of balance.

26Replacement Parts To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, w

27Table & Cabinet Assembly Parts List Index No. Part No. Description Size Qty 1 ... PM3000-101...Cabinet ...

28Trunnion & Motor Assembly

29Trunnion & Motor Assembly Parts List Index No. Part No. Description Size Qty 1 ... PM2000-201...Knob ...

3 Table of Contents Warranty and Service...

30Index No. Part No. Description Size Qty 45 ... PM2000-245...Shaft ...

31Motor Cover Assembly Index No. Part No. Description Size Qty ... 6827044 ...PM2000 Motor Cover Assembly (Index #1 t

32Blade Guard & Miter Gauge Assembly

33Blade Guard & Miter Gauge Assembly Parts List Index No. Part No. Description Size Qty 1 ... PM3000-301...Riving Knife

34Electrical Connections – 7.5HP 3PH 230V 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97GREENBLACKWHITEWHITEBLACKWHITEB

35Electrical Connections – 7.5HP 3PH 460V 5L3A13L213NO1L22T14T26T314NO2T14T26T3A2GROUNDGREENGREENBLACKWHIET959698 97GREENBLACKWHITEWHITEBLACKWHITEB

36 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-

4 Warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on

5 19. Keep visitors a safe distance from the work area. Keep children away. 20. Make your workshop child proof with padlocks, master switches or by

6 Introduction This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for a Powermatic

7 Shipping Contents Unpacking Remove box and wood crating completely from around saw. Check for shipping damage. Report any damage immediately to you

8 Small Box The small box consists of the following items: 1 Push Stick (G) 1 32mm Arbor Wrench (H) 2 Lock Knobs (J) 2 Swivel Handles (K) 1 Rivi

9 Assembly Mounting Extension Wings Referring to Figure 1: 1. Mount a cast iron extension wing (A) to the right or left side of the table (B) using t